A730/A730x Scanner Configuration/Symbologies
You can configure the A730/A730x device in VoiceConsole when creating a device profile.
General Settings
| Configuration | Description | Options |
|---|---|---|
| Message Format Symbology Identifier | Options to configure internal scanners | Disabled Code Mark AIM format User Defined |
| Center Decoding | Only decodes a barcode if it is in the center of the frame. | Disabled Enabled |
| Center Decoding Tolerance | Amount of tolerance for what is considered the center. | Hex value in the range 00 - 64 (do not add a leading "0x"). |
| Decode Mode | Enables 2D label support. | Linear Imager Emulation (barcodes only) 1D/2D Imager Mode |
| Aimer Flashing | Sets the laser aimer mode. | Continuously On Decode Optimized Aimer Off |
| Initial 1D Search Area | Sets the initial search area for 1D barcodes. | Center Upper Half Lower Half Full Image Smart Raster |
| DPM Mode | Enhances the ability to read a Direct Product Marking barcode. | Disabled Enabled |
| Read damaged 1D Codes | Enhances the ability to read damaged or badly printed 1D barcodes. | Disabled Enabled |
| Search Extensively for Barcodes | Causes the decoding algorithms to spend more time trying to find a barcode. | Disabled Enabled |
Postnet
| Configuration | Description | Options |
|---|---|---|
| Postnet Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Transmission (A730 only) |
Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Planet
| Configuration | Description | Options |
|---|---|---|
| Planet Activation | Disabled Enabled |
|
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Transmission (A730 only) |
Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
BPO (British Post Office)
| Configuration | Description | Options |
|---|---|---|
| BPO Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Transmission (A730 only) |
Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Canada Post
| Configuration | Description | Options |
|---|---|---|
| Canada Post Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Australian Post
| Configuration | Description | Options |
|---|---|---|
| Australian Post Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Japan Post
| Configuration | Description | Options |
|---|---|---|
| Japan Post Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Transmission (A730 only) |
Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Dutch Post
| Configuration | Description | Options |
|---|---|---|
| BPO Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Sweden Post
| Configuration | Description | Options |
|---|---|---|
| Sweden Post Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Infomail Post
| Configuration | Description | Options |
|---|---|---|
| Infomail Post Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Intelligent Mail
| Configuration | Description | Options |
|---|---|---|
| Intelligent Post Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. |
Codabar
| Configuration | Description | Options |
|---|---|---|
| Codabar Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification | Enables calculation of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | A user-defined symbology identifier string, from 0 to 4 ASCII characters. | |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| Start/Stop Transmission | Selects start/stop character format to transmit. | Not transmitted a, b, c, d - A, B, C, D a, b, c, d - t, n, *, e DC1, DC2, DC3, DC4 |
| CLSI Library System (A730 only) |
Enables the Computer Library Services, Inc. library standard for Codabar. | Disabled Enabled |
| Concatenation | Multiple label concatenation settings. | Concatenation disabled Only accept concatenated labels Concatenate labels if possible |
| Concatenation Mode | Sets requirements for concatenation. | No requirements 2nd code start = 1st code stop American Blood Commission (start/stop = "d") |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Code93
| Configuration | Description | Options |
|---|---|---|
| Code 93 Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Code39
| Configuration | Description | Options |
|---|---|---|
| Code 39 Activation |
Enables this symbology. |
Disabled Enabled |
| Unconventional (A730 only) |
Allows decoding of unconventional Code 39 (large inter-character spacing or a large ratio between narrow and wide elements). | Disabled Enabled |
| Reading Range | Set to standard or extended. Extended mode uses a special algorithm for increased reading distances. Valid on Code 39 and Trioptic Code 39. | Normal Extended |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification (A730 only) |
Enables calculation of the check digit. | Disabled Enabled |
| Reading Tolerance (A730 only) |
Determines the level of quality that can be read. | High Medium Low |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| Start/Stop Transmission | Selects start/stop character format to transmit. | Disabled Enabled |
| Accepted Start Character (A730 only) |
The accepted start characters for Code 39. | $ (dollar sign) * (asterisk) $ and * |
| Full ASCII Conversion | When Code 39 full ASCII conversion is Enabled, Code 39 barcodes are transmitted with an extended character set. The full ASCII character set is encoded in Code 39 by combining two regular Code 39 characters. | Disabled Enabled |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Code 128
| Configuration | Description | Options |
|---|---|---|
| Code 128 Activation |
Enables this symbology. |
Disabled Enabled |
| ISBT128 Activation | Enables this symbology. If Enabled, Honeywell recommends disabling Code 128 and GS1-128 to avoid decoding confusion. | Disabled Enabled |
| GS1-128 Activation | Enables this symbology. | Disabled Enabled |
| Unconventional GS1-128 | Unconventional decoding mode bitfield. | Range is 0 to 7, where bit 0 = irregular EAN128/GS1-128, bit 1 = FNC2 append disabled, bit 2 = FNC4 ASCII extensions disabled. |
| Reading Range | Set to standard or extended. Extended mode uses a special algorithm for increased reading distances. | Normal Extended |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| GS1-128 Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification (A730 only) |
Enables various calculations of the check digit. | Disabled French CIP |
| Reading Tolerance (A730 only) |
Determines the level of quality that can be read. | High Medium Low |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Code 128, GS1-128, ISBT Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| GS1-128 Identifier (A730 only) |
Enables transmission of AIM identifier before the data. This is ignored if GTIN is active. | Disabled Enabled |
| Separator Character (A730 only) |
Separator between multiple concatenated barcodes. | |
| ISBT 128 Concatenation transmission (A730 only) |
Concatenate two adjacent code 128 barcodes and transmit as one ISBT128 barcode. Usual applications on blood bags in healthcare environment. | Concatenation disabled Only accept concatenated labels Concatenate labels if possible |
| ISBT 128 Concatenation (A730 only) |
Allow non-compliant ISBT barcodes to be concatenated. | Authorized ISBT code pairs ONLY All ISBT code pairs |
| GTIN Processing for GS1-128 (A730 only) |
Limits valid GS1-128 barcodes to Global Trade Item Number compliant format. | Disabled Enabled |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Interleaved 2 of 5
| Configuration | Description | Options |
|---|---|---|
| Interleaved 2 of 5 Activation |
Enables this symbology. |
Disabled Enabled |
| Reading Range (A730 only) |
Set to standard or extended. Extended mode uses a special algorithm for increased reading distances. | Standard Extended |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification | Enables various calculations of the check digit. | Disabled Modulo 10 French CIP HR |
| Reading Tolerance (A730 only) |
Determines the level of quality that can be read. | High Medium Low |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Matrix 2 of 5
| Configuration | Description | Options |
|---|---|---|
| Matrix 2 of 5 Activation |
Enables this symbology. |
Disabled Enabled |
| Start/Stop (A730 only) |
Enable transmission of start/stop characters and checksum. Uses special ChinaPost mode when Enabled, where a specific start/stop is required and the checksum is transmitted. | Regular (Not transmitted) Chinapost (specific start/stop and checksum) |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
MSI Code
| Configuration | Description | Options |
|---|---|---|
| MSI Code Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the barcode data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification | Enables various calculations of the check digit. | Modulo 10 Double Modulo 10 |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission (A730 only) |
Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Plessey Code
| Configuration | Description | Options |
|---|---|---|
| Plessey Code Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Standard 2 of 5
| Configuration | Description | Options |
|---|---|---|
| Standard 2 of 5 Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification | Enables various calculations of the check digit. | Disabled Enabled (Modulo 10) |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission (A730 only) |
Enable transmission of the check digit. | Disabled Enabled |
| Format | Specifies read mode. | Identicon (6 start/stop bars) Computer Identics (4 start/stop bars) |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Telepen
| Configuration | Description | Options |
|---|---|---|
| Telepen Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| Format | Specifies read mode. | ASCII Numeric |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Code 11
| Configuration | Description | Options |
|---|---|---|
| Code 11 Activation |
Enables this symbology. |
Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Check Digit Verification | Select the number of check digits for Code 11 check digit verification. | 1 Digit 2 Digits |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L3 (A730 only) |
Length value L3. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1, L2, L3 are fixed lengths (A730 only) L1/L2 are min/max lengths |
| Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
EAN-UPC
| Configuration | Description | Options |
|---|---|---|
| UPC-A Activation |
Enables this symbology. |
Disabled Enabled |
| UPC-E Activation |
Enables this symbology. |
Disabled Enabled |
| EAN-8 Activation |
Enables this symbology. |
Disabled Enabled |
| EAN-13 Activation |
Enables this symbology. |
Disabled Enabled |
| ISBN Conversion for EAN-13 (A730 only) |
Converts EAN-13 barcodes starting with "978" or "979" (except for "9790") to ISBN (International Standard Book Number) format. No conversion is done if GTIN processing is active. | Disabled Enabled |
| Add-On 2 | Enables decoding of 2-digit EAN-UPC supplements. | Disabled Enabled |
| Add-On 5 | Enables decoding of 5-digit EAN-UPC supplements. | Disabled Enabled |
| Add-On Digit Security (A730 only) |
Selects how much time is spent looking for add-on digits when add-on digits are Enabled but not required. Range is Hex 00 - 64, where 0 is the least amount of time. | HEX value in the range 00 - 64. (Do not add a leading "0x".) |
| UPC-A Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| UPC-E Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| EAN-8 Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| EAN-13 Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| UPC-E1 Activation | Enables the UPC-E1 variant of UPC-E. | Disabled Enabled |
| Reading Range | Set to standard or extended. Extended mode uses a special algorithm for increased reading distances. | Normal Extended |
| UPC-A Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| UPC-E Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| EAN-8 Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| EAN-13 Check Digit Transmission | Enable transmission of the check digit. | Disabled Enabled |
| UPC-A Number System Transmission | Enables transmission of the UPC-A number system. | Disabled Enabled |
| UPC-E Number System Transmission | Enables transmission of the UPC-E number system. | Disabled Enabled |
| UPC-A Transmitted as EAN-13 | Enables conversion of UPC-A to EAN-13. | Disabled Enabled |
| UPC-E Transmitted as UPC-A | Enables conversion of UPC-E to UPC-A. | Disabled Enabled |
| EAN-8 Transmitted as EAN-13 (A730 only) |
Enables conversion of EAN-8 to EAN-13. | Disabled Enabled |
| Add-On Digits | Add on digit requirements. | Optional (transmitted if read) Required and transmitted |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
PDF417
| Configuration | Description | Options |
|---|---|---|
| PDF417 Activation |
Enables this symbology. |
Disabled Enabled |
| Micro PDF417 Activation | Enables the "micro" variant of PDF417. | Disabled Enabled |
| Irregular PDF (A730 only) |
Enables the reading of labels with a symbol length descriptor of 0. | Disabled Enabled |
| Code 128 Emulation (A730 only) |
Sets the AIM identifier to EAN128 if the scanned label contains an EAN128-compatible flag. | Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Micro PDF417 Code Mark (A730 only) |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Optional Fields File Name Transmission (A730 only) |
Enables file name transmission. | Disabled Enabled |
| Segment Count Transmitted (A730 only) |
Enables segment count transmission. | Disabled Enabled |
| Time Stamp Transmitted (A730 only) |
Enables time stamp transmission. | Disabled Enabled |
| Sender Transmitted (A730 only) |
Enables sender transmission. | Disabled Enabled |
| Addressee Transmitted (A730 only) |
Enables addressee transmission. | Disabled Enabled |
| File Size Transmitted (A730 only) |
Enables file size transmission. | Disabled Enabled |
| Checksum Transmitted (A730 only) |
Enables checksum transmission. | Disabled Enabled |
| PDF147 User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
| Micro PDF417 User Defined Symbology Identifier (A730 only) |
User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Codablock
| Configuration | Description | Options |
|---|---|---|
| CodablockA Activation (A730 only) |
Enables this symbology. | Disabled Enabled |
| CodablockF Activation | Enables this symbology. | Disabled Enabled |
| CodablockA Code Mark (A730 only) |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| CodablockF Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| CodablockA User Defined Symbology Identifier (A730 only) |
User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
| CodablockF User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
TLC39
| Configuration | Description | Options |
|---|---|---|
| TLC39 Activation | Enables this symbology. | Disabled Enabled |
| Linear Only Transmission Mode (A730 only) |
Ignores Micro PDF417 data and only transmits the Code 39 portion. | Disabled Enabled |
| ECI Security (A730 only) |
Selects how much time is spent looking for an ECI number if the Code 39 portion of the label is 6 digits. Range is Hex 00 - 64, where 0 is the least amount of time. | HEX value in the range 00 - 64 (Do not add a leading "0x"). |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
GS1 Databar
| Configuration | Description | Options |
|---|---|---|
| Databar OmniDirectional Activation (A730 only) |
Enables this symbology. |
Disabled Enabled |
| Databar Limited Activation (A730 only) |
Enables this symbology. |
Disabled Enabled |
| Databar Expanded Activation (A730 only) |
Enables this symbology. |
Disabled Enabled |
| Omni-Directional Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Limited Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Expanded Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| OmniDirectional User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
| Limited User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
| Expanded User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Maxicode
| Configuration | Description | Options |
|---|---|---|
| Maxicode Activation | Enables this symbology. | Disabled Enabled |
| Mode 0 (A730 only) |
Enables this symbology. | Disabled Enabled |
| Mode 0 Header (A730 only) |
Header for mode 0 labels. | Regular (AIM) Extended (same as mode 2/3) |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Aztec
| Configuration | Description | Options |
|---|---|---|
| Aztec Activation | Enables this symbology. | Disabled Enabled |
| Structured Append (A730 only) |
Enable or disable Aztec structured append mode. If Enabled, the Aztec structured append header is used instead of ECI. | Disabled Enabled |
| Aztec Runes | If Enabled, Aztec Runes - which are special Aztec symbols - can be decoded. | Disabled Enabled |
| Aztec EAN 128 Emulation (A730 only) |
Sets the AIM identifier to EAN128 if the scanned label contains an EAN128-compatible flag. | Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Datamatrix
| Configuration | Description | Options |
|---|---|---|
| Datamatrix Activation | Enables this symbology. | Disabled Enabled |
| Mirrored Labels Activation (A730 only) |
Enables decoding of mirrored labels. | Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
QR Code
| Configuration | Description | Options |
|---|---|---|
| QRCode Activation | Enables this symbology. | Disabled Enabled |
| Inverse Video (A730 only) |
Allow only normal (black barcode, white background), inverted, or both types of labels. | Normal Inverted Automatic (both) |
| Unconventional Structured Append (A730 only) |
Enable transmission of label header as first 2 bytes of every symbol. | Disabled Enabled |
| MicroQR Activation (A730 only) |
Enables the "micro" variant of QR. | Disabled Enabled |
| Code Mark | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
GS1 Composite
| Configuration | Description | Options |
|---|---|---|
| GS1 Composite A-B Activation |
Enables this symbology. |
Disabled Enabled |
| GS1 Composite C Activation |
Enables this symbology. |
Disabled Enabled |
| GS1-128 Emulation | Enables emulation of the GS1-128 symbology. | Normal Inverted Automatic (both) |
| Linear Only Transmission Mode | Ignores the 2D portion, and only transmits the 1D barcode. | Disabled Enabled |
| Unconventional | When enabled, this prevents automatic transmission of AIM identifier. | Disabled Enabled |
| Code Mark CC-A-B | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| Code Mark CC-C | Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| UPC and EAN composite message decoding | Decode mode for EAN/UPC composites, choose if EAN/UPC is linked to the 2D composite component. |
Never linked (Only EAN/UPC) Always linked (EAN/UPC and 2D component) |
| CompositeAB User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
| CompositeC User Defined SymbA single character inserted before the data to indicate the Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
IATA 2 of 5
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| IATA 2 of 5 Activation |
Enables this symbology. |
Disabled Enabled |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1/L2 are min/max lengths. |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User-Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
TriOptic
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| TriOptic Activation |
Enables this symbology. |
Disabled Enabled |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Code 32
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| Code 32 Activation |
Enables this symbology. |
Disabled Enabled |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
China Post
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| China Post Activation |
Enables this symbology. |
Disabled Enabled |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1/L2 are min/max lengths |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Korea Post
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| Korea Post Activation |
Enables this symbology. |
Disabled Enabled |
| Barcode Length L1 | Length value L1. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length L2 | Length value L2. | Full 2-digit hex representation only. No leading "0x". |
| Barcode Length Mode | Length verification mode. | L1 is minimum length L1/L2 are min/max lengths |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
USPS 4-State
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| USPS4 Activation |
Enables this symbology. |
Disabled Enabled |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
Coupon Code
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| Coupon Code Activation |
Enables this symbology. |
Disabled Enabled |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User-Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
ID Tag
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| ID Tag Activation |
Enables this symbology. |
Disabled Enabled |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |
HanXin
This symbology is supported for A730x only.
| Configuration | Description | Options |
|---|---|---|
| HanXin Activation |
Enables this symbology. |
Disabled Enabled |
|
Code Mark |
Single character inserted before the data to indicate the symbology. | Full 2-digit hex representation only. No leading "0x". |
| User-Defined Symbology Identifier | User-defined symbology identifier string. | From 0 to 4 ASCII characters. |